Zyxel-communications ISDN Terminal Adapter Omni.Net Lite User Manual

Omni.Net LiteISDN Terminal AdapterUser’s GuideVer si on 1 . 25/2005

Omni.Net Lite User’s Guide9 Table of Contents2.4 RS-232 Port: Local DN (Directory Number) and Call Type ...282.4.1 Intro

Omni.Net Lite User’s GuideTable of Contents 103.3.1 Data Command Sets ...

Omni.Net Lite User’s Guide11 Table of ContentsChapter 6Troubleshooting ...

Omni.Net Lite User’s GuideList of Figures 12List of FiguresFigure 1 TA and ISDN Interfaces ...

Omni.Net Lite User’s Guide13 List of Figures

Omni.Net Lite User’s GuideList of Tables 14List of TablesTable 1 Top Panel LED Description ...

Omni.Net Lite User’s Guide15 List of Tables

Omni.Net Lite User’s GuidePreface 16PrefaceCongratulations on your purchase of the Omni.Net Lite ISDN Terminal Adapter.Note: Register your product onl

Omni.Net Lite User’s Guide17 Preface• The Omni.Net Lite ISDN Terminal Adapter may be referred to as the TA in this user’s guide.

Omni.Net Lite User’s GuideChapter 1 Introduction 18CHAPTER 1IntroductionThis chapter introduces the key features of the TA.1.1 About your TAThe Omni.

Omni.Net Lite User’s Guide19 Chapter 1 Introduction1.1.1.5 Bandwidth-On-DemandThe TA dynamically allocates bandwidth by dialing and dropping connecti

Omni.Net Lite User’s GuideChapter 1 Introduction 20Figure 1 TA and ISDN InterfacesNote: Do not connect this TA to a U interface.1.2 TA Hardware and

Omni.Net Lite User’s Guide21 Chapter 1 Introduction1.4 Configuration MethodsTo configure your TA, choose one of the following methods:• UtilityLNK On

Omni.Net Lite User’s GuideChapter 1 Introduction 22• AT commands with a terminal emulation program such as Hyperterminal in Windows• Tone commands usi

Omni.Net Lite User’s Guide23 Chapter 1 Introduction

Omni.Net Lite User’s GuideChapter 2 Using the Utility 24CHAPTER 2Using the UtilityThis chapter shows you how to access and configure the TA using the

Omni.Net Lite User’s Guide25 Chapter 2 Using the Utilityyour computer. Otherwise, select Default Settings and click Next to view the default settings

Omni.Net Lite User’s GuideChapter 2 Using the Utility 262.2 Navigating the UtilityThis section summarizes how to navigate the utility.Figure 3 ZyXE

Omni.Net Lite User’s Guide27 Chapter 2 Using the Utility2.3 SystemClick System to display the screen as shown next. Select your country from the Coun

Omni.Net Lite User’s GuideChapter 2 Using the Utility 28Figure 4 System2.4 RS-232 Port: Local DN (Directory Number) and Call TypeThis section shows

Omni.Net Lite User’s GuideCopyright 2CopyrightCopyright © 2005 by ZyXEL Communications Corporation.The contents of this publication may not be reprodu

Omni.Net Lite User’s Guide29 Chapter 2 Using the UtilityFigure 5 Point-to-Point Link Pathway2.4.2 Multilink PPP (MP or MLP)There are two B channels

Omni.Net Lite User’s GuideChapter 2 Using the Utility 302.4.4 ISDN ProtocolsHDLC (High-Level Data Link Control) is one of the most common data link (

Omni.Net Lite User’s Guide31 Chapter 2 Using the UtilityFigure 6 RS-232 Port: Local DN and Call TypeThe following table describes the labels in this

Omni.Net Lite User’s GuideChapter 2 Using the Utility 322.5 RS-232 Port: PPP/MP ParametersThis section shows you how to configure PPP or MP parameter

Omni.Net Lite User’s Guide33 Chapter 2 Using the UtilityFigure 7 Windows XP: Dial-up Connection: Property Figure 8 Windows XP: Dial-up Connection

Omni.Net Lite User’s GuideChapter 2 Using the Utility 34Figure 9 Windows 98: Dial-up Connection Property: Server TypesIf you choose MLP 128K (dynami

Omni.Net Lite User’s Guide35 Chapter 2 Using the UtilityNote: The high threshold must be greater than the low threshold, otherwise, both of them will

Omni.Net Lite User’s GuideChapter 2 Using the Utility 362.6 RS-232 Port: V.24 SignalThe V.24 signal screen describes ways to treat data control signa

Omni.Net Lite User’s Guide37 Chapter 2 Using the UtilityNote: The TA and the computer should use the same flow control protocol.2.6.2 Configuring V.2

Omni.Net Lite User’s GuideChapter 2 Using the Utility 38The following table describes the labels in this screen.2.7 Incoming Call ScreeningUse this f

Omni.Net Lite User’s Guide3 Federal Communications Commission (FCC) Interference StatementFederal CommunicationsCommission (FCC) InterferenceStatement

Omni.Net Lite User’s Guide39 Chapter 2 Using the UtilityFigure 13 RS-232 Port: Incoming Call Screen2.8 Outgoing Call ScreeningUse this function to

Omni.Net Lite User’s GuideChapter 2 Using the Utility 40Figure 14 Analog Port: Outgoing Call Screen2.9 Pre-stored NumbersTo store a phone number fo

Omni.Net Lite User’s Guide41 Chapter 2 Using the UtilityFigure 15 Analog Port: Pre-stored Numbers2.10 RS-232 Port: Advance SettingUse this screen t

Omni.Net Lite User’s GuideChapter 2 Using the Utility 42Figure 16 RS-232 Port: Advance SettingThe following table describes the labels in this scree

Omni.Net Lite User’s Guide43 Chapter 2 Using the Utility2.11 Analog Port: Local DN and OptionsThis section shows you how to assign the phone number(s

Omni.Net Lite User’s GuideChapter 2 Using the Utility 442 Enter the first number in the Address field beside Port 1 and the second number in the Addre

Omni.Net Lite User’s Guide45 Chapter 2 Using the Utility2.11.3 Dialing MethodThere are two ways to send a message containing the phone number: EN-BLO

Omni.Net Lite User’s GuideChapter 2 Using the Utility 46The following table describes the labels in this screen.2.12 Voice CallsThis section covers h

Omni.Net Lite User’s Guide47 Chapter 2 Using the Utility2.12.2 Answering a Voice CallTo answer an incoming call, just pick the receiver when that tel

Omni.Net Lite User’s GuideChapter 2 Using the Utility 48• Call Hold• Call Waiting• Call transfer• Three-Way ConferenceNote: To take full advantage of

Omni.Net Lite User’s GuideSafety Warnings 4Safety WarningsFor your safety, be sure to read and follow all warning notices and instructions.• To reduce

Omni.Net Lite User’s Guide49 Chapter 2 Using the UtilityPress the flash key and then “0” to disconnect the call presently on hold and keep the current

Omni.Net Lite User’s GuideChapter 2 Using the Utility 50Figure 18 Analog Port: Supplementary Service2.12.4.4 Call TransferYou can transfer a call t

Omni.Net Lite User’s Guide51 Chapter 2 Using the Utility4 Hang up the phone.2.12.4.5 Three-Way Conference1 When you are on the phone talking to someo

Omni.Net Lite User’s GuideChapter 3 Using AT Commands 52CHAPTER 3Using AT Commands3.1 AT Commands OverviewAn AT Command is a command in asynchronous

Omni.Net Lite User’s Guide53 Chapter 3 Using AT Commands3 Enter a descriptive name and select an icon in the Connection Description screen. Click OK t

Omni.Net Lite User’s GuideChapter 3 Using AT Commands 54• No parity, 8 data bits, 1 stop bit, flow control set to hardware6 The DTR LED is on. If it i

Omni.Net Lite User’s Guide55 Chapter 3 Using AT Commands3.3 AT CommandsThe following tables summarize the AT command sets.3.3.1 Data Command SetsThe

Omni.Net Lite User’s GuideChapter 3 Using AT Commands 56O Change from escape mode to data mode.+++ is the escape sequence code that is entered in data

Omni.Net Lite User’s Guide57 Chapter 3 Using AT CommandsW2 Display user data.W3 Display phone number of calling site and user data.X Enable/Disable ex

Omni.Net Lite User’s GuideChapter 3 Using AT Commands 58%D3=n The number of retrying to re-dial the outgoing data call once TA failed to establish the

Omni.Net Lite User’s Guide5 ZyXEL Limited WarrantyZyXEL Limited WarrantyZyXEL warrants to the original end user (purchaser) that this product is free

Omni.Net Lite User’s Guide59 Chapter 3 Using AT Commands3.3.2 Command Sets for Analog PortsThe AT command sets for the analog port are shown in the f

Omni.Net Lite User’s GuideChapter 3 Using AT Commands 60\Zd=<phone number> [/<sub-address>]Set a pre-stored phone number for the analog po

Omni.Net Lite User’s Guide61 Chapter 3 Using AT Commands3.3.3 Debug Command SetsThe AT command sets for debugging are shown in the following table.3.

Omni.Net Lite User’s GuideChapter 3 Using AT Commands 623.4.1 Phone Number AssignmentEnter AT!pS=<phone number> and press [ENTER] to assign the

Omni.Net Lite User’s Guide63 Chapter 3 Using AT CommandsFigure 20 AT Command Example 23.4.3 Setting Ports PriorityTo set the same priority for both

Omni.Net Lite User’s GuideChapter 3 Using AT Commands 643.4.6 Call Bumping (Bandwidth Release) for Voice CallsRefer to Section 2.5.2 on page 34 for m

Omni.Net Lite User’s Guide65 Chapter 3 Using AT Commands3.4.8.2 Voice CallUse AT!pId=<phone number> [/<sub-address>] to configure a list

Omni.Net Lite User’s GuideChapter 3 Using AT Commands 663.5 Result CodesA result code is the command response or the connect message to the computer

Omni.Net Lite User’s Guide67 Chapter 3 Using AT Commands

Omni.Net Lite User’s GuideChapter 4 Using Tone Commands 68CHAPTER 4Using Tone CommandsYou can also use a telephone keypad to configure the TA using to

Omni.Net Lite User’s GuideCustomer Support 6Customer SupportPlease have the following information ready when you contact customer support.• Product mo

Omni.Net Lite User’s Guide69 Chapter 4 Using Tone Commands4.2 Tone CommandsThe tone command sets are shown in the following table. Refer to the corre

Omni.Net Lite User’s GuideChapter 4 Using Tone Commands 704.3 Configuring Example with Tone CommandsThis section shows you some examples of configuri

Omni.Net Lite User’s Guide71 Chapter 4 Using Tone Commands4.3.2 Storing Phone NumberTo store a phone number on the TA, use the 13d*<phone number&g

Omni.Net Lite User’s GuideChapter 5 Firmware Upgrade 72CHAPTER 5Firmware UpgradeYou can upgrade TA firmware using the utility or by terminal emulation

Omni.Net Lite User’s Guide73 Chapter 5 Firmware UpgradeFigure 24 Utility Firmware Upgrade: Confirm5 The following screen displays while firmware upl

Omni.Net Lite User’s GuideChapter 5 Firmware Upgrade 742 Type AT$D99 and press [ENTER]. A message “Remote Firmware Upgrade Start...” shows in the next

Omni.Net Lite User’s Guide75 Chapter 5 Firmware Upgrade5 Choose the 1K Xmodem protocol. Type the firmware file's location, or click Browse to sea

Omni.Net Lite User’s GuideChapter 5 Firmware Upgrade 767 After the firmware upload process has completed, the TA automatically restarts. You can check

Omni.Net Lite User’s Guide77 Chapter 5 Firmware Upgrade

Omni.Net Lite User’s GuideChapter 6 Troubleshooting 78CHAPTER 6TroubleshootingThis chapter covers potential problems and possible remedies. After each

Omni.Net Lite User’s Guide7 Customer SupportUNITED [email protected] +44 (0) 8702 909090 www.zyxel.co.uk ZyXEL Communications UKLtd.,11, The

Omni.Net Lite User’s Guide79 Chapter 6 Troubleshooting

Omni.Net Lite User’s GuideIndex 80IndexNumerics110V AC 4230V AC 4AAC 4Accessories 4Airflow 4American Wire Gauge 4AT Commands 55AT Commands Overview 52

Omni.Net Lite User’s Guide81 IndexEElectric Shock 4Electrical Pipes 4Electrocution 4En-Bloc Sending 45Europe 4Exposure 4FFCC 3Finland, Contact Informa

Omni.Net Lite User’s GuideIndex 82Pipes 4Point-To-Point Protocol 28Pool 4Ports Priority 46, 47, 63Power Adaptor 4Power Cord 4Power Outlet 4Power Suppl

Omni.Net Lite User’s Guide83 IndexWorldwide Contact Information 6XX.75 30XON/XOFF 36ZZyXEL Limited WarrantyNote 5

Omni.Net Lite User’s GuideTable of Contents 8Table of ContentsCopyright ....................